american accurate components, inc. thin film precision chip resistors 188 technology drive, unit h, irvine, ca 92618 tel: 9494539888 fax: 9494538889 email: sales@aacix.com 1 schematic dimensions (mm) wraparound termination size l w c d t 0201 0.60 + 0.05 0.30 + 0.05 0.13 + 0.05 0.25+0.05 0.25 + 0.05 0402 1.00 + 0.05 0.5+0.1 0.05 0.20 + 0.10 0.25+0.05 0.10 0.35 + 0.05 0603, p 1.60 + 0.10 0.80 + 0.10 0.20 + 0.10 0.30+0.20 0.10 0.50 + 0.10 0805, p 2.00 + 0.15 1.25 + 0.15 0.40 + 0.25 0.30+0.20 0.10 0.50 + 0.15 1206, p 3.20 + 0.15 1.60 + 0.15 0.45 + 0.25 0.40+0.20 0.10 0.60 + 0.15 1210 3.20 + 0.15 2.60 + 0.15 0.50 + 0.30 0.40+0.20 0.10 0.60 + 0.10 1217 3.00 + 0.20 4.20 + 0.20 0.80 + 0.30 0.80 + 0.25 0.9 max 2010 5.00 + 0.15 2.60 + 0.15 0.50 + 0.30 0.40+0.20 0.10 0.70 + 0.10 2020 5.08 + 0.20 5.08 + 0.20 0.80 + 0.30 0.80 + 0.30 0.9 max 2045 5.00 + 0.15 11.5+ 0.30 0.80 + 0.30 0.80 + 0.30 0.9 max 2512 6.30 + 0.15 3.10 + 0.15 0.60 + 0.25 0.50 + 0.25 0.60 + 0.10 construction figure (wraparound) construction materials item part material resistor nichrome thin film protective film polymide epoxy resin electrode a grounding layer nichrome thin film b electrode layer copper thin film c barrier layer nickel plating d solder layer solder plating (sn) substrate alumina & marking epoxy resin the resistance value is on the front side the production month is on the backside the content of this specification may change withou t notification 05/15/2015 how to order ct 10 - 1003 b x m packaging m = std. reel o = cutting tape tcr (ppm/ c) l = + 1 p = + 5 y = + 50 m = + 2 q = + 10 z = + 100 n = + 3 x = + 25 tolerance (%) u=+ .01 a=+ .05 c=+ .25 f=+ 1 p=+ .02 b=+ .10 d=+ .50 eia resistance value standard decade values size 01=2512 05=0402 10=0805 10p=0805p 11=2020 12=2010 13=1217 14=1210 16=0603 16p=0603p 18=1206 18p=1206p 20=0201 series ct = lead free thin film precision resistors sn termination features high power available 0603p 1/8w, 0805p 1/4w, 1206p 1/2w nichrome thin film resistor element antileaching nickel barrier terminations very tight tolerances, as low as 0.01% extremely low tcr, as low as 1ppm reference standard = iec 601158, jis c 52018
american accurate components, inc. thin film precision chip resistors 188 technology drive, unit h, irvine, ca 92618 tel: 9494539888 fax: 9494538889 email: sales@aacix.com 2 electrical characteristics size power rating at 70 (w) resistance range % tolerance tcr (10 -6 / c) working voltage overload voltage operating temp range 0201 0.05 22 ~ 75k 0.1, 0.5, 1.0 25 50 100 25v 50v 55 c ~ +125 c 1k ~ 10k 0.05 10 0402 0.063 10.0 ~ 46.4 0.1, 0.5, 1 10, 25, 50 50v 100v 55 c ~ +125 c 47.0 ~ 97.6 0.05, 0.1, 0.25, 0.5, 1 10, 25, 50 100 ~ 2.94k 0.02, 0.05, 0.1, 0.25, 0.5, 1 5, 10, 25, 50 3.00k ~ 100k 0.05, 0.1, 0.25, 0.5, 1 10, 25, 50 0603 0.063 0.100 10.0 ~ 100k 0.01, 0.02, 0.05, 0.1, 0.25, 0.5, 1 1,2,3,5,10,25,5 0 75v 150v 55 c ~ +125 c 102k ~ 270k 0.05, 0.1, 0.25, 0.5, 1 10, 25, 50 55 c ~ +125 c 274k ~ 360k 0.1, 0.25, 0.5, 1 10, 25, 50 0603p 0.125 1.0 9.1 0.5, 1 50, 100 75v 150v 55 c ~ +125 c 10 390k 0.1, 1.0 10, 25, 50, 100 0805 0.100 10.0 ~ 200k 0.01, 0.02, 0.05, 0.1, 0.25, 0.5, 1 1, 2, 3, 5, 10, 25, 50 100v 200v 55 c ~ +125 c 205k ~ 360k 0.05, 0.1, 0.25, 0.5 10, 25, 50 365k ~ 487k 0.05, 0.1, 0.25, 0.5 10, 25 499k ~ 1.00m 0.1, 0.5 25 0805p 0.250 1.0 9.1 0.5, 1 50, 100 150v 300v 55 c ~ +125 c 10 800k 0.1, 1.0 10, 25, 50, 100 1206 0.125 5.01 ~ 560k 0.01, 0.02, 0.05, 0.1, 0.25, 0.5, 1 1, 2, 3, 5, 10, 25, 50 150v 300v 55 c ~ +125 c 562k ~ 1.00m 0.05, 0.1, 0.25, 0.5 10, 25 1206p 0.500 1.0 9.1 0.5, 1 50, 100 150v 300v 55 c ~ +125 c 10 ~ 1.00m 0.1, 1.0 10, 25, 50, 100 1210 0.250 100 ~ 330k 0.1 5, 10 200v 400v 55 c ~ +125 c 51.0 ~ 2.00m 0.1, 0.5 25 10.0 ~ 49.9 0.5 50 1217 0.250 5.10 ~ 1.00m 0.01, 0.02, 0.05, 0.1, 0.25, 0.5, 1 1, 2, 3, 5, 10, 25 200v 400v 55 c ~ +155 c 2010 0.250 100 ~ 20.0k 0.01, 0.05, 0.1, 0.25, 0.5 5 150v 300v 55 c ~ +125 c 50.0 ~ 40.0k 0.01, 0.05, 0.1, 0.25, 0.5 10 10.0 ~500k 0.01, 0.05 25 4.70 1.00m 0.1, 0.25, 0.5, 1 10.0 ~500k 0.01, 0.05 50 1.00 ~ 1.00m 0.1, 0.25, 0.5, 1 2020 0.500 5.10 ~ 2.00m 0.01, 0.02, 0.05, 0.1, 0.25, 0.5, 1 1, 2, 3, 5, 10, 25 350v 700v 55 c ~ +155 c 2045 1.000 20.0 ~ 4.99m 0.01, 0.02, 0.05, 0.1, 0.25, 0.5, 1 1, 2, 3, 5, 10, 25 500v 1000v 55 c ~ +155 c 2512 0.500 100 ~ 20.0k 0.01, 0.05, 0.1, 0.25, 0.5 5 150v 300v 55 c ~ +125 c 50.0 ~ 40.0k 0.01, 0.05, 0.1, 0.25, 0.5 10 10.0r ~ 500k 0.01, 0.05 25 4.70 1.00m 0.1, 0.25, 0.5, 1 10.0r ~ 500k 0.01, 0.05 50 1.00 1.00m 0.1, 0.25, 0.5, 1 * rated voltage: pxr
american accurate components, inc. thin film precision chip resistors 188 technology drive, unit h, irvine, ca 92618 tel: 9494539888 fax: 9494538889 email: sales@aacix.com 3 performance & environmental specifications test item maximum +0.05 (tolerance) condition a b, c d, f short time overload 0.1% 0.1% 0.5% 2.5 times of the rated voltage shall be applied for 5 second s load life 0.1% 0.25% 0.5% the resistor shall be subjected to rated voltage fo r 90 min. followed by a pause of 30 min. at a temperature of 703oc. this constitut es 1 cycle. cycles shall be repeated for 1000 hours. moisture load life 0.1% 0.25% 0.5% the resistor subjected to rated voltage for 90 min followed by a pause for 30 min at a temperature of 602oc with relative humidity o f 90% to 95%. this constitutes 1 cycle. cycles shall be repeated for 1000 hours. temperature cycle 0.1% 0.1% 0.5% [55oc 30 min +125oc 30 min r.t. 3 min] the resistor shall be subjected to 5 continuous cycles resistance to solder heat 0.05% 0.1% 0.5% the resistor shall withstand dipped into solder for 10 1 sec. at 2605oc terminal strength 0.1% 0.1% 0.5% distance bet ween fulcrums: 90mm; bending width: 3 mm solderability a new uniform coating of solder shall cover minimum of 95% of surface being immersed the resistor shall be dipped into the solder of 235 5oc for 30.5 seconds insulation resistance dc 500v for 1 minute 1000 meg or over value marking for those parts ordered with an e24 value, the pro duct will be marked with a 3 digit code. for those products ord ered with an e96 value, the product will be marked with a 4 dig it code. for those parts which fall under e96 and e24 values ( e.g. 1k ohm is both an e96 and e24 value), the part will be m arked with a 3 digit code; 4 digit markings for this type is avail able upon special request. 0201, and 0402 size no marking e24 & e96 values custom value any size 0603 size eia 96 digit code of 3.32k ohm e96 values 0603 ~ 2512 sizes eia 3 digit code of 10k ohm resistor e24 values, e96 values 0805 ~ 2512 sizes eia 4 digit code of 121k ohm resistor e96 values label description one side surface of a reel is marked with a label w ith the following items of information. 1. chip resistor 2. part number 3. tolerance 4. quantity 5. lot number for production month/year* 6. manufacturers name or symbol * the suffix l indicates that this item is lead f ree. as of september 2004, all new production items of the series cr and cj are no lon ger containing tin/lead (snpb) terminals; they are lead free and in compliance wit h lead free/rohs. package quantity type 0201 0402 0603 0805 1206 m 5,000 10,000 5,000 5,000 5,000 o 1,000 1,000 1,000 1,000 1,000 type 1210 1217 2010 2020 2045 2512 b 5,000 2,000 4,000 2,000 3,000 4,000 o 1,000 1,000 1,000 1,000 1,000 1,000 reel schematic & dimensions (mm ) o & m type m type 7 reel 13 reel c ? 13 0.2 ? 13 0.2 e 60 0.5 100 0.2 f 11.4 1.0 13.5 1.0 g 9.0 0.3 9.5 0.5 h 1.5 0.3 2.0 0.5 m ? 180 2.0 ? 330 2.0 reel size is dependent upon the package quantity& resistor size. call for more info. tape sche matic tape dimensions (mm) 0201 0402 0603 0805 1206 a 0.41 0.1 0.65 0.1 1.1 0.1 1.6 0.15 2.0 0.15 b 0.71 0.1 1.15 0.1 1.9 0.1 2.4 0.2 3.6 0.2 w 8.0 0.2 8.0 0.2 8.0 0.2 8.0 0.2 8.0 0.2 e 1.75 0.10 1.75 0.10 1.75 0.1 1.75 0.1 1.75 0.1 f 3.5 0.05 3.5 0.05 3.5 0.05 3.5 0.05 3.5 0.05 p 1 2.0 0.05 2.0 0.05 4.0 0.1 4.0 0.1 4.0 0.1 t 0.5 max 0.55 0.1 0.64 0.1 0.84 0.1 0.84 0.1 t p 0.4+ 0.05 0.40 0.05 1210 1217 2010 2020 2045 2512 a 2.9 0.1 3.5 0.1 2.9 0.1 5.5 0.1 5.4 0.1 2.9 0.1 b 3.5 0.1 4.9 0.1 5.3 0.1 5.5 0.1 11.9 0.1 5.3 0.1 w 8.0 0.2 12.0 0.2 12.0 0.2 12.0 0.2 24.0 0.2 12.0 0.2 e 1.75 0.1 1.75 0.1 1.75 0.1 1.75 0.1 1.75 0.1 1.75 0.1 f 3.5 0.05 5.5 0.1 5.5 0.1 5.5 0.1 11.5 0.1 5.5 0.05 p 1 4.0 0.1 8.0 0.1 4.0 0.1 8.0 0.1 8.0 0.1 4.0 0.1 t 0.90 0.1 0.90 0.1 1.0 0.1 1.0 0.1 1.0 0.1 1.0 0.1 t p 0.75 0.1 0.25 0.1 0.25 0.1 51b 1213 103
|